Measuring before ordering saves a return trip: the thread diameter of the existing lever body, the distance from the lever mounting to the flush valve connection point, and whether the arm needs to sit above or below the water line all affect which replacement will actually fit. A lever bought to the wrong thread size will not seal against the cistern wall, however well the rest of the job goes.
See more on this at flexible hose supplier.
A siphon uses the physics of siphoning rather than a simple valve seal to move water from the cistern into the pan. Lifting the lever raises a plastic or rubber diaphragm inside the siphon body, which pushes a slug of water up and over a bend in the siphon tube, starting a siphoning action that then draws the rest of the cistern's contents down through the tube by suction until the water level drops low enough to break the siphon and stop the flush. This is why older cisterns produce that distinctive extended flush sound rather than the quicker valve-open, valve-close action of a modern flush valve.
A flush valve, by contrast, works as a straightforward seal at the base of the cistern that lifts to let water fall directly through into the pan under gravity, with no siphoning action involved, and shuts again once the float or timer mechanism allows it to reseat. Flush valves are what almost all dual-flush cisterns use, since a siphon's all-or-nothing action makes a genuine short flush difficult to achieve, plumb2u.com whereas a valve can simply be held open for a shorter or longer period.
Noise is a real factor when deciding between the two. A side-entry valve introducing water above the surface tends to produce more splash and a higher-pitched fill sound, which shows up as a complaint on quieter properties such as flats with shared walls. Bottom-entry valves that fill below the surface are noticeably quieter, and swapping a noisy side-entry unit for a bottom-entry equivalent is a common upgrade even where nothing has technically failed.
Fixing centres, meaning the distance between the two mounting holes in the pan, is the measurement that actually determines whether a seat will fit at all, and it varies enough between manufacturers that assuming a standard spacing is a common source of returned parts. The two most frequently seen spacings in the UK are around 140mm to 145mm and 160mm to 165mm centre to centre, and a seat bought for the wrong spacing simply will not sit over both holes.
See more on this at flexible hose supplier.
A siphon uses the physics of siphoning rather than a simple valve seal to move water from the cistern into the pan. Lifting the lever raises a plastic or rubber diaphragm inside the siphon body, which pushes a slug of water up and over a bend in the siphon tube, starting a siphoning action that then draws the rest of the cistern's contents down through the tube by suction until the water level drops low enough to break the siphon and stop the flush. This is why older cisterns produce that distinctive extended flush sound rather than the quicker valve-open, valve-close action of a modern flush valve.
A flush valve, by contrast, works as a straightforward seal at the base of the cistern that lifts to let water fall directly through into the pan under gravity, with no siphoning action involved, and shuts again once the float or timer mechanism allows it to reseat. Flush valves are what almost all dual-flush cisterns use, since a siphon's all-or-nothing action makes a genuine short flush difficult to achieve, plumb2u.com whereas a valve can simply be held open for a shorter or longer period.
Noise is a real factor when deciding between the two. A side-entry valve introducing water above the surface tends to produce more splash and a higher-pitched fill sound, which shows up as a complaint on quieter properties such as flats with shared walls. Bottom-entry valves that fill below the surface are noticeably quieter, and swapping a noisy side-entry unit for a bottom-entry equivalent is a common upgrade even where nothing has technically failed.
Fixing centres, meaning the distance between the two mounting holes in the pan, is the measurement that actually determines whether a seat will fit at all, and it varies enough between manufacturers that assuming a standard spacing is a common source of returned parts. The two most frequently seen spacings in the UK are around 140mm to 145mm and 160mm to 165mm centre to centre, and a seat bought for the wrong spacing simply will not sit over both holes.