The flush plate itself is usually the first point of failure a customer notices, whether that is a button that has stopped actuating, a plate that has come loose from the wall, or a dual-flush mechanism that only performs a full flush regardless of which button is pressed. Because the plate connects to the cistern through a spindle or cable rather than sitting directly on top of it, the fault could sit at the plate, along the linkage, or at the flush valve itself, and each of those needs a different part.
Before ordering, it helps to note the frame's brand if it is visible on the tank or access panel, along with the fill valve and flush valve dimensions if the old parts can be measured before removal. Plumb2U stocks fill valves, flush valves, cables, spindles and flush plates suited to the concealed cisterns most commonly found in UK homes, at trade prices, which helps when a plumber is working blind on a job where the tank itself cannot be seen until the access plate is off. With next-day despatch available on the common models, Plumb2U's stock list is worth checking against the frame details before committing to a specific part.
Before placing an order, it pays to note three things on site: whether the cistern sits flush to the pan or is wall-mounted above it, plumb2u.com the fill valve's body length if there is a tight fit inside the tank, and whether the existing lever operates through the lid or via an external arm. Plumb2U carries fill valves, flush valves and levers suited to both close-coupled and low-level cisterns, stocked at trade prices for plumbers who need to get the right part on the first order rather than the second. Trade supplies despatch from Plumb2U's Epsom base to plumbers across the UK, and Plumb2U remains a straightforward call when the cistern type is not obvious from the pan alone.
Once inside, the cistern behind a concealed frame is usually a compact, purpose-built tank rather than a standard visible cistern, and the fill valve and flush valve fitted to it are sized to fit that specific frame's depth and width. This is where sourcing spares gets harder than for a standard cistern: frame manufacturers often specify particular valve models to fit their tank dimensions, and a valve that works fine in a standard low-level cistern may simply not fit inside a concealed frame's tighter cavity.
A close-coupled cistern bolts directly onto the back of the pan with no visible pipework between the two. Because the outlet on the cistern base sits directly above the inlet on the pan, the flush valve or siphon needs a shorter outlet and often a rubber doughnut washer to seal the joint rather than a length of pipe. Fill valves on close-coupled units tend to be shorter in the body too, since there is less depth inside a compact tank.
A stiff lever is often nothing more than a nut inside the cistern that has worked loose or over-tightened against the tank wall, throwing the lever arm out of alignment with the flush valve linkage below. Loosening the retaining nut, straightening the arm and re-tightening to a snug but free-moving fit resolves a surprising number of stiff-lever callouts without needing a single new part.
Before ordering, it helps to note the frame's brand if it is visible on the tank or access panel, along with the fill valve and flush valve dimensions if the old parts can be measured before removal. Plumb2U stocks fill valves, flush valves, cables, spindles and flush plates suited to the concealed cisterns most commonly found in UK homes, at trade prices, which helps when a plumber is working blind on a job where the tank itself cannot be seen until the access plate is off. With next-day despatch available on the common models, Plumb2U's stock list is worth checking against the frame details before committing to a specific part.
Before placing an order, it pays to note three things on site: whether the cistern sits flush to the pan or is wall-mounted above it, plumb2u.com the fill valve's body length if there is a tight fit inside the tank, and whether the existing lever operates through the lid or via an external arm. Plumb2U carries fill valves, flush valves and levers suited to both close-coupled and low-level cisterns, stocked at trade prices for plumbers who need to get the right part on the first order rather than the second. Trade supplies despatch from Plumb2U's Epsom base to plumbers across the UK, and Plumb2U remains a straightforward call when the cistern type is not obvious from the pan alone.
Once inside, the cistern behind a concealed frame is usually a compact, purpose-built tank rather than a standard visible cistern, and the fill valve and flush valve fitted to it are sized to fit that specific frame's depth and width. This is where sourcing spares gets harder than for a standard cistern: frame manufacturers often specify particular valve models to fit their tank dimensions, and a valve that works fine in a standard low-level cistern may simply not fit inside a concealed frame's tighter cavity.
A close-coupled cistern bolts directly onto the back of the pan with no visible pipework between the two. Because the outlet on the cistern base sits directly above the inlet on the pan, the flush valve or siphon needs a shorter outlet and often a rubber doughnut washer to seal the joint rather than a length of pipe. Fill valves on close-coupled units tend to be shorter in the body too, since there is less depth inside a compact tank.
A stiff lever is often nothing more than a nut inside the cistern that has worked loose or over-tightened against the tank wall, throwing the lever arm out of alignment with the flush valve linkage below. Loosening the retaining nut, straightening the arm and re-tightening to a snug but free-moving fit resolves a surprising number of stiff-lever callouts without needing a single new part.