Alfa Laval offers a versatile range of small-scale LabStak™ plate-and-frame modules for on-site membrane testing. Advanced capabilities including AFM, zeta potential analysis, and specialized microscopy reveal fundamental mechanisms governing membrane behavior. Contact angle measurement and SEM analysis form the basic toolkit, enabling rapid morphological assessment. Chemical compatibility testing exposes membranes to cleaning chemicals and operational solutions, assessing durability and dimensional stability. Mechanical stability assessment cycles membranes between operational and rest conditions, identifying potential failure modes. This fundamental parameter enables meaningful comparison between membranes of different materials and structures.
Alfa Laval filtration lab testing solutions
Tensile strength testing is a fundamental method for characterising the mechanical properties of waterproofing membranes, coatings, and other materials and… Specialists in compatibility testing Weathering UV Exposure Testing of waterproofing systems used in conjunction with tile adhesives. NATA Accredited specialists in the testing of liquid and sheet waterproof membranes, with full range of testing capabilities for internal and external wet areas.
CSIRO / APAS Specification AP-S4003 Waterproofing Membranes For Wet Areas
With a focus on quality, precision and speed, ITA is a trusted and reliable industry-leading material testing partner. With Alfa Laval’s expertise, you gain reliable insights that drive efficiency and innovation in your operations. Compare performance in real time through simultaneous testing of up to five different membrane types, saving time and resources when optimizing production processe
Dunlop Pro Rapid Tape is a self-adhesive sealing tape that provides a waterproofing seal between the surface joints of the… A self-adhesive waterproofing joint tape provides a seal between the surface joints of the floor and wall, under shower grates and… • Dries to a keyed finish to promote direct tile adhesion – suitable for use in conjunction with all cement based tile adhesives that conform to AS2358.
Dunlop Timber Joint Seala
SESA Technicians can make recommendations not only on the type of test that is appropriate, but also make recommendations on the selection of sites that should be tested. When applied in this way, the dry floor friction test method can indicate the effectiveness of a cleaning regime. Where the surface is generally wet and used in barefoot conditions, choose the wet barefoot ramp method (Appendix C). Such surfaces are primarily designed to provide drainage or entrapment of contaminant materials.
About Zerofal
This can mean that an initial inclining platform classification of R9, the lowest inclining platform test rating, may fail to meet an inclining platform classification in-situ due to the slope of the surface on which the material is installed. An inclining platform method does not mean that the surface is necessarily used as an inclining platform. In any case, at least one of Appendix A, C or D should be used for all external pedestrian surfaces and internal surfaces that have a reasonably foreseeable risk of the presence of wet substances such as water, grease and oil.
Obligations under the State/Territory Wrongs Act also provide for an owner/occupier responsibility for the safety of visitors to the premises. SESA slip resistance testing Technicians are occupational hygienists and safety professionals trained to perform floor slip tests to Australian Standards. Turn to SESA for all your Floor Slip Resistance Testing requirements in Sydney, Canberra, Wollongong, Newcastle and other areas across NSW and AC
Membrane manufacturing can be technically challenging and in the last few years Weathering UV Exposure Testing the membrane centre has established a new laboratory for purpose of developing new membrane material for gases and liquid. We have the experience and resources to ensure your accreditation provides you and your organisation with unique advantages. Our active role in international accreditation education has seen us conduct training in over 20 countries. NATA has been training individuals and teams both nationally and internationally for over 20 years and enjoys a global reputation for the quality of its courses and programs. NATA members receive a globally-recognised, peer-reviewed and government endorsed accreditation that provides a unique level of assurance to members, their clients and the communit
We strongly believe their accreditation provides the formal recognition that PoCT produces reliable, technical results. NATA accreditation is both nationally and internationally recognised. The Global Accreditation Cooperation Incorporated has become Global ACI the next evolution of the single international body uniting ILAC and IAF. In 2020, Approval Specialists P/L and Austest Laboratories became part of the Phenna Group, a UK based Group of specialist businesses focused on the Testing, Inspection, Certification, and Compliance (TICC) Sector. Contact Test Australia for truly independent assessment with NATA-accredited laboratory analysis -- results you can trust because no one has a financial interest in the outcom
Alfa Laval filtration lab testing solutions
Tensile strength testing is a fundamental method for characterising the mechanical properties of waterproofing membranes, coatings, and other materials and… Specialists in compatibility testing Weathering UV Exposure Testing of waterproofing systems used in conjunction with tile adhesives. NATA Accredited specialists in the testing of liquid and sheet waterproof membranes, with full range of testing capabilities for internal and external wet areas.
CSIRO / APAS Specification AP-S4003 Waterproofing Membranes For Wet Areas
With a focus on quality, precision and speed, ITA is a trusted and reliable industry-leading material testing partner. With Alfa Laval’s expertise, you gain reliable insights that drive efficiency and innovation in your operations. Compare performance in real time through simultaneous testing of up to five different membrane types, saving time and resources when optimizing production processe
Dunlop Pro Rapid Tape is a self-adhesive sealing tape that provides a waterproofing seal between the surface joints of the… A self-adhesive waterproofing joint tape provides a seal between the surface joints of the floor and wall, under shower grates and… • Dries to a keyed finish to promote direct tile adhesion – suitable for use in conjunction with all cement based tile adhesives that conform to AS2358.
Dunlop Timber Joint Seala
SESA Technicians can make recommendations not only on the type of test that is appropriate, but also make recommendations on the selection of sites that should be tested. When applied in this way, the dry floor friction test method can indicate the effectiveness of a cleaning regime. Where the surface is generally wet and used in barefoot conditions, choose the wet barefoot ramp method (Appendix C). Such surfaces are primarily designed to provide drainage or entrapment of contaminant materials.
About Zerofal
This can mean that an initial inclining platform classification of R9, the lowest inclining platform test rating, may fail to meet an inclining platform classification in-situ due to the slope of the surface on which the material is installed. An inclining platform method does not mean that the surface is necessarily used as an inclining platform. In any case, at least one of Appendix A, C or D should be used for all external pedestrian surfaces and internal surfaces that have a reasonably foreseeable risk of the presence of wet substances such as water, grease and oil.
Obligations under the State/Territory Wrongs Act also provide for an owner/occupier responsibility for the safety of visitors to the premises. SESA slip resistance testing Technicians are occupational hygienists and safety professionals trained to perform floor slip tests to Australian Standards. Turn to SESA for all your Floor Slip Resistance Testing requirements in Sydney, Canberra, Wollongong, Newcastle and other areas across NSW and AC
Membrane manufacturing can be technically challenging and in the last few years Weathering UV Exposure Testing the membrane centre has established a new laboratory for purpose of developing new membrane material for gases and liquid. We have the experience and resources to ensure your accreditation provides you and your organisation with unique advantages. Our active role in international accreditation education has seen us conduct training in over 20 countries. NATA has been training individuals and teams both nationally and internationally for over 20 years and enjoys a global reputation for the quality of its courses and programs. NATA members receive a globally-recognised, peer-reviewed and government endorsed accreditation that provides a unique level of assurance to members, their clients and the communit
We strongly believe their accreditation provides the formal recognition that PoCT produces reliable, technical results. NATA accreditation is both nationally and internationally recognised. The Global Accreditation Cooperation Incorporated has become Global ACI the next evolution of the single international body uniting ILAC and IAF. In 2020, Approval Specialists P/L and Austest Laboratories became part of the Phenna Group, a UK based Group of specialist businesses focused on the Testing, Inspection, Certification, and Compliance (TICC) Sector. Contact Test Australia for truly independent assessment with NATA-accredited laboratory analysis -- results you can trust because no one has a financial interest in the outcom