Read more from buy plumbing parts online.
The flush valve tells a different story. If water is draining slowly from the cistern into the pan even when nobody has touched the button or handle, the flush valve seal or siphon washer has likely perished and is no longer sealing the outlet at the base of the tank. This shows up as a cistern that refills every few minutes with no obvious trigger, sometimes described by customers as topping itself up rather than running continuously. On older gravity-fed systems built around a siphon rather than a valve, a split diaphragm inside the siphon body produces the same symptom.
Start with the fill valve. This is the mechanism that lets water into the cistern after a flush and shuts off once the tank reaches the correct level, usually via a float or a diaphragm. When a fill valve wears, the most common signs are a hissing or trickling noise that continues long after the cistern should have stopped filling, a water level creeping up to or past the overflow pipe, or a float arm that no longer rises high enough to trigger shut-off. Mineral deposits inside the valve seat are often the culprit, particularly in hard water softener supplier UK areas, and once the seal degrades a full replacement is usually more reliable than trying to clean it out.
A siphon uses the physics of siphoning rather than a simple valve seal to move water from the cistern into the pan. Lifting the lever raises a plastic or rubber diaphragm inside the siphon body, which pushes a slug of water up and over a bend in the siphon tube, starting a siphoning action that then draws the rest of the cistern's contents down through the tube by suction until the water level drops low enough to break the siphon and stop the flush. This is why older cisterns produce that distinctive extended flush sound rather than the quicker valve-open, valve-close action of a modern flush valve.
Locating the access plate is the first practical step, and it is not always where it looks like it should be. Some concealed frames put the service access behind the flush plate itself, which simply hinges or unclips forward once the buttons are removed, while others use a separate panel elsewhere on the same wall or in an adjoining space such as an airing cupboard. Getting this wrong before checking the frame manufacturer's layout wastes time working into a wall that did not need opening.
Cable-actuated systems use a flexible cable in place of the rigid spindle, which allows the button to be positioned somewhere other than directly above the flush valve, useful on concealed cisterns and certain close-coupled designs where the lid mechanism does not line up with the valve beneath. The cable itself can stretch, kink or seize inside its outer sheath over time, and a button that has become stiff, or one that no longer springs back after use, usually points to the cable rather than the flush valve itself.
The flush valve tells a different story. If water is draining slowly from the cistern into the pan even when nobody has touched the button or handle, the flush valve seal or siphon washer has likely perished and is no longer sealing the outlet at the base of the tank. This shows up as a cistern that refills every few minutes with no obvious trigger, sometimes described by customers as topping itself up rather than running continuously. On older gravity-fed systems built around a siphon rather than a valve, a split diaphragm inside the siphon body produces the same symptom.
Start with the fill valve. This is the mechanism that lets water into the cistern after a flush and shuts off once the tank reaches the correct level, usually via a float or a diaphragm. When a fill valve wears, the most common signs are a hissing or trickling noise that continues long after the cistern should have stopped filling, a water level creeping up to or past the overflow pipe, or a float arm that no longer rises high enough to trigger shut-off. Mineral deposits inside the valve seat are often the culprit, particularly in hard water softener supplier UK areas, and once the seal degrades a full replacement is usually more reliable than trying to clean it out.
A siphon uses the physics of siphoning rather than a simple valve seal to move water from the cistern into the pan. Lifting the lever raises a plastic or rubber diaphragm inside the siphon body, which pushes a slug of water up and over a bend in the siphon tube, starting a siphoning action that then draws the rest of the cistern's contents down through the tube by suction until the water level drops low enough to break the siphon and stop the flush. This is why older cisterns produce that distinctive extended flush sound rather than the quicker valve-open, valve-close action of a modern flush valve.
Locating the access plate is the first practical step, and it is not always where it looks like it should be. Some concealed frames put the service access behind the flush plate itself, which simply hinges or unclips forward once the buttons are removed, while others use a separate panel elsewhere on the same wall or in an adjoining space such as an airing cupboard. Getting this wrong before checking the frame manufacturer's layout wastes time working into a wall that did not need opening.
Cable-actuated systems use a flexible cable in place of the rigid spindle, which allows the button to be positioned somewhere other than directly above the flush valve, useful on concealed cisterns and certain close-coupled designs where the lid mechanism does not line up with the valve beneath. The cable itself can stretch, kink or seize inside its outer sheath over time, and a button that has become stiff, or one that no longer springs back after use, usually points to the cable rather than the flush valve itself.