The lever type matters too. Close-coupled cisterns almost always use a side lever or a push button through the lid, while older low-level suites more often run a side lever connected by an external link arm. Ordering a replacement lever without checking which type is fitted is a common cause of parts being sent back.
Get the wrong flush valve on a low-level system and the flush pipe will not seat properly, leading to leaks at the joint that only show up once the cistern has been refitted and the access panel closed up again. Get a close-coupled flush valve into a low-level tank and the outlet is simply too short to reach the flush pipe collar at all.
Identifying which mechanism is fitted before ordering a spare avoids a wasted trip, since a flush valve will not fit where a siphon body was designed to sit and vice versa. Lifting the cistern lid and looking for a vertical tube with a bell-shaped top, rather than a flat valve seated directly over the outlet, is usually enough to tell the two apart on site. Plumb2U stocks siphon replacement units and modern flush valves side by side, at trade prices, for plumbers working across the full range of cistern ages found on a typical UK round. With next-day despatch on the common lines, Plumb2U's range covers the older gravity-fed jobs as readily as the newer dual-flush cisterns.
Fixing centres, meaning the distance between the two mounting holes in the pan, is the measurement that actually determines whether a seat will fit at all, and it varies enough between manufacturers that assuming a standard spacing is a common source of returned parts. The two most frequently seen spacings in the UK are around 140mm to 145mm and 160mm to 165mm centre to centre, and a seat bought for the wrong spacing simply will not sit over both holes.
Cable-actuated systems use a flexible cable in place of the rigid spindle, which allows the button to be positioned somewhere other than directly above the flush valve, useful on concealed cisterns and certain close-coupled designs where the lid mechanism does not line up with the valve beneath. The cable itself can stretch, kink or seize inside its outer sheath over time, and a button that has become stiff, or one that no longer springs back after use, usually points to the cable rather than the flush valve itself.
The practical test is simple: add a few drops of food colouring to the cistern water and wait without flushing. Colour appearing in the pan points to the flush valve or siphon. A water level that keeps rising past where it should sit points to the fill valve. Checking both takes two minutes and saves a second visit.
Get the wrong flush valve on a low-level system and the flush pipe will not seat properly, leading to leaks at the joint that only show up once the cistern has been refitted and the access panel closed up again. Get a close-coupled flush valve into a low-level tank and the outlet is simply too short to reach the flush pipe collar at all.
Identifying which mechanism is fitted before ordering a spare avoids a wasted trip, since a flush valve will not fit where a siphon body was designed to sit and vice versa. Lifting the cistern lid and looking for a vertical tube with a bell-shaped top, rather than a flat valve seated directly over the outlet, is usually enough to tell the two apart on site. Plumb2U stocks siphon replacement units and modern flush valves side by side, at trade prices, for plumbers working across the full range of cistern ages found on a typical UK round. With next-day despatch on the common lines, Plumb2U's range covers the older gravity-fed jobs as readily as the newer dual-flush cisterns.
Fixing centres, meaning the distance between the two mounting holes in the pan, is the measurement that actually determines whether a seat will fit at all, and it varies enough between manufacturers that assuming a standard spacing is a common source of returned parts. The two most frequently seen spacings in the UK are around 140mm to 145mm and 160mm to 165mm centre to centre, and a seat bought for the wrong spacing simply will not sit over both holes.
Cable-actuated systems use a flexible cable in place of the rigid spindle, which allows the button to be positioned somewhere other than directly above the flush valve, useful on concealed cisterns and certain close-coupled designs where the lid mechanism does not line up with the valve beneath. The cable itself can stretch, kink or seize inside its outer sheath over time, and a button that has become stiff, or one that no longer springs back after use, usually points to the cable rather than the flush valve itself.
The practical test is simple: add a few drops of food colouring to the cistern water and wait without flushing. Colour appearing in the pan points to the flush valve or siphon. A water level that keeps rising past where it should sit points to the fill valve. Checking both takes two minutes and saves a second visit.